lcm600 600 watt bulk front end total power: 600 w # of outputs: single outputs: 12 to 60 v optional 5.0 v standby special features ? 600 w output power ? low cost ? 2.4 x 4.5 x 7.5 ? 7.41 w/cu-in ? industrial/medical safety ? -40 c to 70 c with derating ? optional 5 v @ 2 a housekeeping ? high effciency: 89% typical ? variable speed smart fans ? dsp controlled front end ? conformal coat option ? 20% adjustment range ? margin programming ? or-ing fet ? terminal block input option compliance ? emi class b ? en61000 immunity safety ? ul/csa ul60950-1/csa c22.2 no. 60950-1 ? tuv en60950-1 ? cb report iec60950-1 ? ccc gb4943, gb9254 and gb17625 ? ul/csa es60601-1/csa c22.2 no. 60601-1 ? tuv en60601-1 ? cb report iec60601-1 electrical specifcations input input ra nge 85 - 264 vac (operating) 115/230 vac (nominal) input through standard iec connector/ terminal block frequency 47 - 440 hz, nominal 50/60 input fusing internal 10 a fuses, both lines fused inrush current 25 a peak, either hot or cold start power factor 0.99 typical, meets en61000-3-2 harmonics meets iec 1000-3-2 requirements input current 8 a rms max input current, at 100 vac hold up time 20 ms minimum for main o/p, at full rated load effciency > 89% at full load leakage current < 0.3 ma at 264 vac on/off power switch n/a power line transient mov directly after the fuse isolation isolation: pri-chassis 2500 vdc basic pri-sec 4000 vac reinforced 2xmopp sec-chassis 500 vdc lcm600q efciency without the 5 vsb 76.00 78.00 80.00 82.00 84.00 86.00 88.00 90.00 92.00 25 50 75 100 lo ad ing % e fc ie nc y % 100 va c 230 va c data sheet power
environmental specifcations operating temperature -40 c to +70 c, linear derating to 50% from 50 c to 70 c storage temperature -40 c to +85 c humidity 10 to 90%, non-condensing. operating. conformal coat option available. fan noise < 45 dba, 80% load at 30 c -n low noise option < 35 dba, 80% load at 30 c altitude operating - 16,404.2 feet storage - 30,000 feet shock mil-std-810f 516.5, procedure i, vi. storage vibration mil-std-810f 514.5, cat. 4, 10. storage electrical specifcations output output rating see ordering information table 85 - 264 vac set point 0.5% 85 - 264 vac total regulation range main output 2% 5 vsb 1% combined line/load/transient when measured at output terminal rated load 600 w maximum derate linear to 50% from 50 c to 70 c minimum load main output @ 0.0 a 5 vsb @ 0.0 a no loss of regulation output noise (pard) 1% max p-p 50 mv max p-p main output 5 vsb output measured with a 0.1 f ceramic and 10 f tantalum capacitor on any output, 20 mhz output voltage overshoot no overshoot/undershoot outside the regulation band during on or off cycle transient response < 300 sec 50% load step @ 1 a/s step load valid between 10% to 100% of output rating recovery time to within 1% of set point at onset of transient max units in parallel up to 10 short circuit protection protected, no damage to occur bounce mode remote sense compensation up to 500 mv output isolation standard per safety requirements forced load sharing to within 10% of all shared outputs analog sharing control overload protection (ocp) 105% to 125% 120% to 170% main output 5 vsb output overvoltage protection (ovp) 125% to 145% 110% to 125% 12 v output 5 vsb output overtemp protection 10 - 15 c above safe operating area both pfc and output converter monitored fan fault protection for-n option only. will shutdown output and dc_ok ordering information model number* output nominal output voltage set point set point tolerance adjustment range current output ripple p/p (0-50 ?c) max continuous power combined line/ load regulation min max lcm600l 12 v 12 v 0.5% 9.6 - 14.4 v 0 a 52 a 120 mv 600 w 2% lcm600n 15 v 15 v 0.5% 12.0 - 19.5 v 0 a 44 a 150 mv 600 w 2% lcm600q 24 v 24 v 0.5% 19.2 - 28.8 v 0 a 27 a 240 mv 600 w 2% LCM600U 36 v 36 v 0.5% 28.8 - 43.2 v 0 a 16.7 a 240 mv 600 w 2% lcm600w 48 v 48 v 0.5% 38.4 - 57.6 v 0 a 14 a 280 mv 600 w 2% *note: add -t for terminal block instead of iec input add -n for low noise model on 12 v or 24 v models add -4 for 5 v standby output add -a will be automatically added to all orders to denote new aesthetics style chassis unless otherwise specifed example: a 24 v with terminal block, low noise and standby with new aesthetics would be lcm600q-t-n-4-a lcm600 data sheet
pin assignment signals name description pin number(s) +vout power rail sk4 gnd power gnd sk5 signals name description sk2 pin number a2 eeprom address 1 -vprog return connection of external supply for margin programming 2 a1 eeprom address 3 -vsense remote sense return 4 ishare load share voltage 5 a0 eeprom address 6 sda1 serial data signal (i2c) 7 +vprog positive connection of external supply for margin programming 8 scl1 serial clock signal (i2c) 9 +vsense remote sense positive 10 5vsb 5v standby 11 gnd 5v standby return 12 5vsb 5v standby 13 g_dcok_c global dcok collector 14 gpioa6 eeprom write protect 15 g_dcok_e global dcok emitter (gnd) 16 gnd return ground for output signal and i2c communication 17 g_acok_c global acok collector 18 inh_en turn off main output 19 g_acok_e global acok emitter (gnd) 20 led indicators two (2) provided are clearly visible up to a 45 degree offset from vertical with offce environment ambient lighting. the status is refected in the indicator color. the dc_ok led led is bicolor. it shall light green if the dc output is within specifcation, and amber if the output falls out of specifcation. the ac_ok led led is green if the ac is within specifcation and off when out of specifcation. note: with 5 v standby, amber also indicates that psu is in standby mode/output off. control signals ac_ok open collector 0.5 v maximum at 10 ma. both emitter and collector access provided. dc_ok open collector 0.5 v maximum at 10 ma. both emitter and collector access provided. dc_ok will de-assert when output is loss due to ocp, ovp, otp, or fan fault (for -n option). ps_inhibit/enable signal 0.0 - 0.5 v contact closure, output off signal output signal connectors (sk2) sk2 mating connector: jst part number phdr-20vs; contact pins: jst part number sphd-001t-p0.5 note: mating connector for sk2 is: landwin: pn 2050s2000 housing and pn 2053t021v contact civilux: pn ci0120sd000 housing and pn ci01td21pe0 contact jst: pn phdr-20vs housing and pn: sphd-001t-p0.5 lcm600 data sheet
ordering information lcmxxxxy - a - b - c - ### case size input termination acoustic noise option codes hardware code 1-phase input where xxxx = 600 = 2.4 x 4.5 x 7.5, 600 w blank = iec connector blank = standard blank = no options factory assigned for modiefed standards t = terminal block n = low noise fan 1 = conformal coat voltage code y = 4 = 5 v standby code 5 = opt 1 + 4 l 12 n 15 q 24 u 36 w 48 41 (2x)22 0.5 (2x)47 0.5 62 1 (2x)6 0.5 (2x)182.5 0.5 (2x)10 0.5 (2x)177.5 0.5 11.15 0.5 17.65 0.5 (2x) 94.45 0.5 50 (2x)10.6 114.3 0.5 (18.5) 190.5 0.5 50 (212.2 ref) 16.8 9.5 9.5 screw-mc philip pan with washer m4x8 see detail b detail b ac inlet version input terminal block see note 8 led (dc/ok fail) led (ac ok) sk2 signal connector - 20way sk4 & sk5 (8x) mounting locations both sides m4x0.7p thread see note 7 brand logo see detail a see detail c (trimpot location) (4x) mounting locations m4x0.7p thread see note 7 scale 1.500 detail a ground neutral live detail c (trimpot location) voltage adjustment: clockwise - increase voltage counter clockwise - decrease voltage mechanical drawings note: optional barrier strip output terminal available optional molex type connector output available new mechanical reference drawing: weight: 2.84 lbs (1.29 kg) mounting locations screw penetration depth is 4.6 mm max. recommended screw torque: m3.5 x 0.6p = 6 - 8kgf-cm m4.0 x 0.7p = 8 - 10kgf-cm note 7 recommended screw torque: m3.5x0.6p = 6-8kgf-cm m4.0x0.7p = 8-10kfg-cm note 8 input: terminal block type. m3.5 screw torque value of 12kgf-cm using wire gauge 22-19 (9.5mm centers) lcm600 data sheet
190,5 0,5 18,5 ref 16,8 9,5 9,5 12,8 32,8 114,3 0,5 50 (2x)10,6 15,75 (2x) 22 0,5 40,2 (2x) 47 0,5 61 0,5 (2x) 6 0,5 (2x) 182,5 0,5 17,65 0,5 (2x) 94,45 0,5 11,15 0,5 (2x) 10 0,5 (2x) 177,5 0,5 led (ac ok) led (dc/ok fail) input terminal block see note 8 pos - sk4 neg - sk5 sk2 signal connector - 20way screw-mc philip pan with ext-t washer m3.5 x p0.6 x 6 (8x) mounting locations both sides m4x0.7p thread see note 7 (4x) mounting locations m4x0.7p thread see note 7 provision for future label requirements see detail a product label see detail b (trimpot location) scale 8:5 detail a ground nuetral live detail b (trimpot location) voltage adjustment: clockwise - increase voltage counter clockwise - decrease voltage mechanical drawings C terminal block input old mechanical reference drawing: weight: 2.84 lbs (1.29 kg) note 7 - recommended screw torque: m3.5x0.6p = 6-8kgf-cm m4.0x0.7p = 8-10kfg-cm lcm600 data sheet
low noise vs. non-low noise lcm600 model 30.0 32.0 34.0 36.0 38.0 40.0 42.0 44.0 46.0 48.0 50.0 52.0 54.0 56.0 58.0 60.0 02 .5 57 .5 10 12.5 15 17.5 20 22.5 25 27 .5 30 32 .5 35 37 .5 40 42 .5 45 47.5 50 25 deg ambien t no n- low nois e ve rs io n low nois e ve rs io n lo ad (a ) no is e (d ba 30.0 32.0 34.0 36.0 38.0 40.0 42.0 44.0 46.0 48.0 50.0 52.0 54.0 56.0 58.0 60.0 02 .5 57 .5 10 12. 51 51 7. 52 02 2. 52 52 7. 53 03 2. 53 5 37. 54 04 2. 54 54 7. 55 0 50 deg ambien t no n- low nois e ve rs io n low nois e ve rs io n lo ad (a ) no is e (d ba non-low noise version load (a) 25 ?c ambient 50 ?c ambient fan (v) rpm noise (dba) fan (v) rpm noise (dba) 0 6.254 3558.0 40.9 6.228 3460.9 39.9 2.5 6.257 3559.8 41.0 6.228 3460.9 39.9 5 6.262 3562.0 41.0 6.230 3494.3 40.1 7.5 6.263 3562.0 41.0 6.242 3526.6 40.1 10 6.242 3528.9 40.5 6.242 3526.6 40.1 12.5 6.251 3530.9 40.6 6.237 3515.6 40.4 15 6.251 3538.3 40.7 6.229 3504.9 40.2 17.5 6.226 3538.2 40.7 6.205 3482.8 39.4 20 6.223 3541.0 40.7 6.217 3490.1 40.0 22.5 6.242 3545.1 40.8 6.227 3493.8 40.1 25 6.253 3553.9 40.9 6.234 3504.3 40.2 27.5 6.254 3564.1 41.0 6.212 3501.7 40.2 30 6.253 3552.2 40.9 6.642 3787.4 44.1 32.5 6.264 3559.7 41.0 7.893 4652.3 48.0 35 6.262 3559.6 41.0 9.153 5463.4 50.0 37.5 6.262 3560.8 41.0 11.035 6600.2 52.0 40 6.262 3559.8 41.0 11.605 6993.9 53.2 42.5 7.637 4521.2 47.8 11.608 6997.2 53.2 45 8.919 5362.2 49.3 11.608 6997.2 53.2 47.5 10.068 6139.5 51.0 11.608 6997.2 53.2 50 11.362 6893.4 52.8 11.608 6997.2 53.2 low noise version pwm 25 ?c ambient 50 ?c ambient load (a) rpm noise (dba) load (a) rpm noise (dba) 0% 0 3028 35.2 0 3180 36.0 5% 2.5 3028 35.2 2.5 3300 36.7 10% 5 3028 35.2 5 3300 36.7 15% 7.5 3060 35.4 7.5 3360 37.0 20% 10 3028 35.2 10 3360 37.0 25% 12.5 3028 35.2 12.5 3360 37.0 30% 15 3060 35.4 15 3360 37.0 35% 17.5 3060 35.4 17.5 3388 37.2 40% 20 3028 35.2 20 3388 37.2 45% 22.5 3028 35.2 22.5 3540 38.0 50% 25 3060 35.4 25 3840 39.2 55% 27.5 3028 35.2 27.5 4104 40.2 60% 30 3028 35.2 30 4408 41.4 65% 32.5 3060 35.4 32.5 4736 42.7 70% 35 3060 35.4 35 5184 44.5 75% 37.5 3060 35.4 37.5 5728 46.4 80% 40 3060 35.4 40 6688 49.5 85% 42.5 3420 37.4 42.5 7560 51.8 90% 45 3868 39.3 45 7584 51.9 95% 47.5 4376 41.3 47.5 7584 51.9 100% 50 5040 43.9 50 7584 51.9 lcm600 data sheet
lcm600 ds 14mar2017 accessories miscellaneous specifcations burn-in 100% burn-in at 45 c, at 80 - 90 % load. duration of burn-in determined by quality assurance procedures. mtbf the power supply has a minimum mtbf of 300k hours using the bell core 332, issue 6 specifcation @ 25 c and 40 c, ambient, at full load. with the power supply installed in a system in a 25 c ambient environment and operating at full load, capacitor life shall be 10 years, minimum for all electrolytic capacitors contained within this power supply. the power supply shall demonstrate a mtbf level of > 500,000 hours. quality assurance full qav testing shall be conducted in accordance with artesyn embedded technologies standards with reports available upon request. warranty artesyn embedded technologies shall warrant the power supply to be free of defects in materials and workmanship for a minimum period of three years from the date of shipment, when operated within specifcations. the warranty shall be fully transferable to the end owner of the equipment powered by the supply. order kit part number 73-788-001 for control connector interface with .3m wires attached order kit part number 73-788-002 for control connector interface with unloaded housing and 20 pins pin 20 pin 2 pin 19 pin 1 pin 3 300 5 mm pin 20 pin 2 pin 19 pin 1 pin 3 lcm600 data sheet worldwide offices americas 2900 s.diablo way tempe, az 85282 usa +1 888 412 7832 europe (uk) waterfront business park merry hill, dudley west midlands, dy5 1lx united kingdom +44 (0) 1384 842 211 asia (hk) 14/f, lu plaza 2 wing yip street kwun tong, kowloon hong kong +852 2176 3333 for more information: www.artesyn.com/power for support: productsupport.ep@artesyn.com www.artesyn.com artesyn embedded technologies, artesyn and the artesyn embedded technologies logo are trademarks and service marks of artesyn embedded technologies, inc. all other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. specifications are subject to change without notice. ? 2017 artesyn embedded technologies, inc. all rights reserved. for full legal terms and conditions, please visit www.artesyn.com/legal.
|
